Waterway Spa Hot Tub Pump Wet End 2" X 2" 48 Frame 3 HP Executive Bleeder Barb Kit

Waterway Spa Hot Tub Pump Wet End 2"

You are buying a 3 HP 48 Frame Waterway Executive 2" X 2" Wet End / Pump complete with Bleeder Barb & Silicon, Screws, Volute, Impeller, Seal, Face and the Wear Ring. This Wet End would fit a motor that shows 12.0 Amps on the motor label on high speed.. The Barb and Silicon is used in place of a plug for wet ends that have bleeders on them. Note: 315-1260 means nothing.The difference between a 48 or 56 Frame wet end is the spacing of the Motor Thru bolts. The 48 Frame will be 3 5/8" between or 5 3/16" in a X Pattern and the 56 Frame will be 4 1/8" Between or 5 3/4" in a X Pattern. Look on the label of the motor for the two amperages if you have a 2 speed pump, if its a single speed look for a single amperage. It will look something like this: 10.0/3.5 The 10.0 is the high amperage in this example. 8.0 = 1 HP 10.0 = 2 HP 12.0 = 3 HP 14.0 = 4 HP 16.0 = 5 HP NOTE: Your pump or motor may say a different Horse Power than what you see here, DO NOT go by what is listed on the motor, go by the amperage on the label. Note: Note: Note: There are some cases where a 12 Amp motor has a 4HP impeller so so if your motor has a 12.0 Amp Motor you need to check for the HP cast into the center of the impeller or look at the wear ring.. If the wear ring says 1, 2 or 3 then you have a 3HP impeller if...

  • Brand: American Spa Parts
  • ASIN: B079F53KHQ
  • UPC: 740016014959

Waterway 310-1130SDB 1HP 48 Frame Wet End

Waterway 310-1130SDB 1HP 48 Frame Wet

Waterway 310-1130SDB 1HP 48 Frame Wet End

  • Brand: Waterway Plastics
  • ASIN: B079SG145T
  • UPC: 758614173572

Waterway 310-1870 2" Executive 48 Frame 1HP Wet End Pump

Waterway 310-1870 2" Executive 48 Frame 1HP Wet

This is the Wet End portion of a 1 HP Executive 2" suction, 48Y frame spa pump. This is basically a pump without a motor.This Wet End is used with a 1 HP, 48Y frame, thru-bolt style motor. The motor used may be either a single speed or a two speed. The Wet End may be rotated 90 degrees to change the discharge position.The inlet and outlet are standard 2" buttress threads. See below for exact dimensions. This has a center inlet and side discharge.Features:1 Horsepower48 Frame2" Inlet and 2" Outlet

  • Brand: Waterway
  • ASIN: B00EV7O2A2
  • UPC: 852673911745

Waterway Spa Hot Tub Pump Wet End 2" X 2" 48 Frame 4 HP Executive Bleeder Barb Kit

Waterway Spa Hot Tub Pump Wet End 2"

You are buying a 4 HP 48 Frame Waterway Executive 2" X 2" Wet End / Pump complete with Bleeder Barb & Silicon, Screws, Volute, Impeller, Seal, Face and the Wear Ring. This Wet End would fit a motor that shows 12.0-14.0 Amps on the motor label on high speed.. The Barb and Silicon is used in place of a plug for wet ends that have bleeders on them. Note: 315-1260 means nothing.The difference between a 48 or 56 Frame wet end is the spacing of the Motor Thru bolts. The 48 Frame will be 3 5/8" between or 5 3/16" in a X Pattern and the 56 Frame will be 4 1/8" Between or 5 3/4" in a X Pattern. Look on the label of the motor for the two amperages if you have a 2 speed pump, if its a single speed look for a single amperage. It will look something like this: 10.0/3.5 The 10.0 is the high amperage in this example. 8.0 = 1 HP 10.0 = 2 HP 12.0 = 3 HP 14.0 = 4 HP 16.0 = 5 HP NOTE: Your pump or motor may say a different Horse Power than what you see here, DO NOT go by what is listed on the motor, go by the amperage on the label. Note: Note: Note: There are some cases where a 12 Amp motor has a 4HP impeller so so if your motor has a 12.0 Amp Motor you need to check for the HP cast into the center of the impeller or look at the wear ring.. If the wear ring says 1, 2 or 3 then you have a 3HP impell...

  • Brand: American Spa Parts
  • ASIN: B079F24VGZ
  • UPC: 740016014966

Sundance Spa Pump 2.5HP 48 Frame Complete Wet End (06/2009+) - 6500-343/341

Sundance Spa Pump 2.5HP 48 Frame Complete Wet

  • Brand: Sundance
  • ASIN: B06WGTXGWW

Waterway Spa Hot Tub Pump Wet End 2" X 2" 48 Frame 1 HP Executive Bleeder Barb Kit

Waterway Spa Hot Tub Pump Wet End 2"

You are buying a 1 HP 48 Frame Waterway Executive 2" X 2" Wet End / Pump complete with Bleeder Barb & Silicon, Screws, Volute, Impeller, Seal, Face and the Wear Ring. This Wet End would fit a motor that shows 8.0 Amps at 230V on the motor label on high speed or 12.0 Amps at 115V.. Example 2.8/8.0... The Barb and Silicon is used in place of a plug for wet ends that have bleeders on them. Watch the Videos to learn about how to pick the correct wet end as well as how to repair your wet end and motor bearings too. The difference between a 48 or 56 Frame wet end is the spacing of the Motor Thru bolts. The 48 Frame will be 3 5/8" between or 5 3/16" in a X Pattern and the 56 Frame will be 4 1/8" Between or 5 3/4" in a X Pattern. . We have done a lot of extra work with videos and pictures to prevent you from choosing the wrong part.. Look on the label of the motor for the two amperages if you have a 2 speed pump, if its a single speed look for a single amperage. It will look something like this: 10.0/3.5 The 10.0 is the high amperage in this example. 8.0 = 1 HP 10.0 = 2 HP 12.0 = 3 HP 14.0 = 4 HP 16.0 = 5 HP NOTE: Your pump or motor may say a different Horse Power than what you see here, DO NOT go by what is listed on the motor, go by the amperage on the label. NOTE for the NOTE: TRUST M...

  • Brand: American Spa Parts
  • ASIN: B079F5263J
  • UPC: 740016014935

Intex Krystal Clear Cartridge Filter Pump for Above Ground Pools, 1000 GPH Pump Flow Rate, 110-120V with GFCI

Intex Krystal Clear Cartridge Filter Pump for Above

Keep your pool water Krystal Clear and refreshing this summer with the Intex 1,000 GPH Filter Cartridge Pump! Boasting a pump flow rate of 1,000 gallons per hour and a system flow rate of 750 gallons per hour, this pump will circulate and filter the water in your above ground pool to keep everything clean, refreshing, and fun. In addition, the maintenance for this pump is a breeze: just the occasional cartridge rinse or swap to keep this pump running strong. This filter uses Type A filter cartridges (Item #29000E) which should be changed every couple of weeks. This pump is a must have for any above ground pool up to 15 feet in diameter, see for yourself!

  • Color: Gray
  • Brand: Intex
  • ASIN: B005QIYL7E
  • UPC: 078257316489

Intex 28633EG Krystal Clear Cartridge Filter Pump for Above Ground Pools, 2500 GPH Pump Flow Rate, 110-120V with GFCI

Intex 28633EG Krystal Clear Cartridge Filter Pump for

Keep your pool water Krystal Clear and refreshing this summer with the Intex 2,500 GPH Filter Cartridge Pump! Boasting a pump flow rate of 2,500 gallons per hour and a system flow rate of 1,900 gallons per hour, this pump will circulate and filter the water in your above ground pool to keep everything clean, refreshing, and fun. In addition, the maintenance for this pump is a breeze: just the occasional cartridge rinse or swap to keep this pump running strong. It uses Type B filter cartridges (Item #29005E) which should be changed every couple of weeks. This 2,500 GPH filter pump is the most powerful cartridge filter pump made by Intex, and is a must have for any above ground pool up to 24 feet in diameter, see for yourself! It can be used with any Intex above ground pools and features a built-in timer to set operating times for the ultimate in convenience.

  • Color: Gray
  • Brand: Intex
  • ASIN: B005QIYMNM
  • UPC: 078257316502

Waterway 15-350-1160 Side Discharge Wet End Pump, Hi-Flo, 4.0HP, 2.0"

Waterway 15-350-1160 Side Discharge Wet End Pump, Hi-Flo,

SpaGuts Replacement pump wet end assembly for the Waterway Hi-Flo Side Discharge 48-Frame Pump model. Available in 4.0HP. Both intake and discharge fittings are 2.0 inch. NOTE 1: The 2.0 inch pump wet end assembly has an outside to outside thread measurement of approximately 3.0 inch. NOTE 2: Only purchase this pump wet end assembly as a direct replacement to avoid leaks, fitment and failures. Do not install on 56-Frame motors. This pump wet end is also a replacement option for the following part numbers: 311-2140 (Faceplate), 805-0256 (Faceplate O-Ring), 319-1390 (Wear Ring), 310-4000 (1.0HP Impellar), 310-4010 (1.5HP Impellar), 310-4030 (2.0HP Impellar), 310-4020 (3.0HP Impellar), 310-4050 (4.0HP Impellar), 319-3100B (Shaft Seal Kit), 315-2500 (Side Discharge Volute with Inserts), 313-1400 (Slinger), 715-1201 (3/8" Quarter Slot Drain Plug), 805-0112 (Drain Plug O-Ring). This item comes with a 90-Day limited warranty.

  • Color: Black
  • Brand: Waterway
  • ASIN: B07K4S8PDV
  • UPC: 702811347960

Gecko 91040720-000 1.5"MBT 48 Frame Wet End for 1.5HP FMHP Pump

Gecko 91040720-000 1.5"MBT 48 Frame Wet End for

Gecko 91040720-000 1.5"MBT 48 Frame Wet End for 1.5HP FMHP Pump

  • Brand: Gecko Alliance
  • ASIN: B00L2ONW7G
  • UPC: 682470322594

Gecko Aqua-Flo 91041815-000 Wet End 48Y Frame 1.5HP Flo-Master XP2E Pump

Gecko Aqua-Flo 91041815-000 Wet End 48Y Frame 1.5HP

2" Suction - 2" Side Discharge. Used in Pump: AI #1-00-0131 / MFG #06115517-2040; AI #1-00-0133 / MFG #06115000-1040. Replacement Option For: AI #1-05-0327 / MFG #91041609.

  • Brand: GECKO
  • ASIN: B008NGE8CO
  • UPC: 852673912643

Waterway 15-350-1142 Side Discharge Wet End Pump, Hi-Flo, 2.0HP, 2.0"

Waterway 15-350-1142 Side Discharge Wet End Pump, Hi-Flo,

SpaGuts Replacement pump wet end assembly for the Waterway Hi-Flo Side Discharge 48-Frame Pump model. Available in 2.0HP. Both intake and discharge fittings are 2.0 inch. NOTE 1: The 2.0 inch pump wet end assembly has an outside to outside thread measurement of approximately 3.0 inch. NOTE 2: Only purchase this pump wet end assembly as a direct replacement to avoid leaks, fitment and failures. Do not install on 56-Frame motors. This pump wet end is also a replacement option for the following part numbers: 311-2140 (Faceplate), 805-0256 (Faceplate O-Ring), 319-1390 (Wear Ring), 310-4000 (1.0HP Impellar), 310-4010 (1.5HP Impellar), 310-4030 (2.0HP Impellar), 310-4020 (3.0HP Impellar), 310-4050 (4.0HP Impellar), 319-3100B (Shaft Seal Kit), 315-2500 (Side Discharge Volute with Inserts), 313-1400 (Slinger), 715-1201 (3/8" Quarter Slot Drain Plug), 805-0112 (Drain Plug O-Ring). This item comes with a 90-Day limited .

  • Brand: Waterway
  • ASIN: B07K4W7ZWT
  • UPC: 663001713012

Waterway Spa Hot Tub Pump Wet End 2" X 2" 48 Frame 2 HP Executive Bleeder Barb Kit

Waterway Spa Hot Tub Pump Wet End 2"

You are buying a 2 HP 48 Frame Waterway Executive 2" X 2" Wet End / Pump complete with Bleeder Barb & Silicon, Screws, Volute, Impeller, Seal, Face and the Wear Ring. This Wet End would fit a motor that shows at 230V 10.0 Amps on the motor label on high speed 16.0A at 115V.. Example 2.8/8.0... The Barb and Silicon is used in place of a plug for wet ends that have bleeders on them. Watch the Videos to learn about how to pick the correct wet end as well as how to repair your wet end and motor bearings too. The difference between a 48 or 56 Frame wet end is the spacing of the Motor Thru bolts. The 48 Frame will be 3 5/8" between or 5 3/16" in a X Pattern and the 56 Frame will be 4 1/8" Between or 5 3/4" in a X Pattern. . We have done a lot of extra work with videos and pictures to prevent you from choosing the wrong part.. Look on the label of the motor for the two amperages if you have a 2 speed pump, if its a single speed look for a single amperage. It will look something like this: 10.0/3.5 The 10.0 is the high amperage in this example. 8.0 = 1 HP 10.0 = 2 HP 12.0 = 3 HP 14.0 = 4 HP 16.0 = 5 HP NOTE: Your pump or motor may say a different Horse Power than what you see here, DO NOT go by what is listed on the motor, go by the amperage on the label. NOTE for the NOTE: TRUST ME ON T...

  • Brand: American Spa Parts
  • ASIN: B079F1Y4QW
  • UPC: 740016014942

Waterway Spa Hot Tub Pump Wet End 2" X 2" 48 Frame 5 HP Executive Bleeder Barb Kit

Waterway Spa Hot Tub Pump Wet End 2"

You are buying a 5 HP 48 Frame Waterway Executive 2" X 2" Wet End / Pump complete with Bleeder Barb & Silicon, Screws, Volute, Impeller, Seal, Face and the Wear Ring. This Wet End would fit a motor that shows 16.0 Amps on the motor label on high speed.. The Barb and Silicon is used in place of a plug for wet ends that have bleeders on them. Note: 315-1260 means nothing.The difference between a 48 or 56 Frame wet end is the spacing of the Motor Thru bolts. The 48 Frame will be 3 5/8" between or 5 3/16" in a X Pattern and the 56 Frame will be 4 1/8" Between or 5 3/4" in a X Pattern. Look on the label of the motor for the two amperages if you have a 2 speed pump, if its a single speed look for a single amperage. It will look something like this: 10.0/3.5 The 10.0 is the high amperage in this example. 8.0 = 1 HP 10.0 = 2 HP 12.0 = 3 HP 14.0 = 4 HP 16.0 = 5 HP NOTE: Your pump or motor may say a different Horse Power than what you see here, DO NOT go by what is listed on the motor, go by the amperage on the label. Note: Note: Note: There are some cases where a 12 Amp motor has a 4HP impeller so so if your motor has a 12.0 Amp Motor you need to check for the HP cast into the center of the impeller or look at the wear ring.. If the wear ring says 1, 2 or 3 then you have a 3HP impeller if...

  • Brand: American Spa Parts
  • ASIN: B079F8P78L
  • UPC: 740016014973

Waterway 15-350-1116 Side Discharge Wet End Pump, Hi-Flo, 1.5HP, 2.0"

Waterway 15-350-1116 Side Discharge Wet End Pump, Hi-Flo,

SpaGuts Replacement pump wet end assembly for the Waterway Hi-Flo Side Discharge 48-Frame Pump model. Available in 1.5HP. Both intake and discharge fittings are 2.0 inch. NOTE 1: The 2.0 inch pump wet end assembly has an outside to outside thread measurement of approximately 3.0 inch. NOTE 2: Only purchase this pump wet end assembly as a direct replacement to avoid leaks, fitment and failures. Do not install on 56-Frame motors. This pump wet end is also a replacement option for the following part numbers: 311-2140 (Faceplate), 805-0256 (Faceplate O-Ring), 319-1390 (Wear Ring), 310-4000 (1.0HP Impellar), 310-4010 (1.5HP Impellar), 310-4030 (2.0HP Impellar), 310-4020 (3.0HP Impellar), 310-4050 (4.0HP Impellar), 319-3100B (Shaft Seal Kit), 315-2500 (Side Discharge Volute with Inserts), 313-1400 (Slinger), 715-1201 (3/8" Quarter Slot Drain Plug), 805-0112 (Drain Plug O-Ring). This item comes with a 90-Day limited warranty.

  • Brand: Waterway
  • ASIN: B07K4Q6V37
  • UPC: 663001448334

Gecko AF91040730000 2HP 48 Frame Wet End for Flo-Master Pumps

Gecko AF91040730000 2HP 48 Frame Wet End for

Gecko AF91040730000 2HP 48 Frame Wet End for Flo-Master PumpsSpecifications:Wet End 2 HP 48 Frame FMHP Flo-MasterSpecificationsHorse Power: 2 HP

  • Brand: Gecko Alliance
  • ASIN: B07RZW765S
  • UPC: 682470389641

Gecko Aqua-Flo 91041825-000 Wet End 48Y Frame 2.5HP Flo-Master XP2E Pump

Gecko Aqua-Flo 91041825-000 Wet End 48Y Frame 2.5HP

2" Suction - 2" Side Discharge. Used in Pump: AI #1-00-0093B / MFG #06125000-1040. Replacement Option For: AI #1-05-0329 / MFG #91041611.

  • Color: Black
  • Brand: Gecko
  • ASIN: B008NGE8VU
  • UPC: 852673912667

Waterway Plastics 310-1140SDB Hi-Flo Side Discharge Replacement Wet End for 1-1/2-Horsepower Pump

Waterway Plastics 310-1140SDB Hi-Flo Side Discharge Replacement Wet

This Hi-Flo side discharge replacement wet end is for 1-1/2-horsepower pump. Old style was square with cut corners. Features 2-inch intake and 2-inch discharge. Outside diameter of intake and discharge measures 3-inch. Use with a 48 frame motor. Comes with 1-year warranty.

  • Brand: Waterway Plastics
  • ASIN: B00C7UF6Y6
  • UPC: 806105196569

Intex 15' x 33" Prism Frame Above Ground Swimming Pool Set with Pump | 28721EH

Intex 15' x 33" Prism Frame Above Ground

Intex Prism Frame Pools are inspired by the line of Ultra Frame Pools with many of the same features, but with smaller dimensions and at more affordable price points. This unique design accommodates smaller yards, making a Prism Frame Pool from Intex the perfect fit for anyone with limited yard space. The Intex Prism Frame Pool is constructed using strong, powder-coated steel tubing that is UV and rust resistant. The liner features an attractive blue/gray color scheme with mosaic tile print on the inside and is manufactured using super-tough, puncture-resistant, 3-ply PVC material. The Prism Frame Pool from Intex was also designed with a convenient built-in drain plug so you never have to pump out water to empty the pool. The Prism Frame Pool Kit from Intex Includes: 530 Gallon Cartridge Filter Pump, Complete DIY Instructions, and Instructional Set-Up DVD. Dimensions: 15 Feet Round x 33 Inches Tall. Intex Model: 28721EH.

  • Color: Blue
  • Brand: Intex
  • ASIN: B01N97L5MA
  • UPC: 078257322626

Agri-Fab 18-Inch x 36-Inch Poly Tow Lawn Roller 45-0268

Agri-Fab 18-Inch x 36-Inch Poly Tow Lawn Roller

Restore a lawn’s smooth appearance after flooding or eliminate frost heaves with this heavyweight lawn roller from Agri-Fab. Users fill the roller’s drum with up to 400 pounds of water or sand and hook it up behind a tractor. The tractor tows the roller over lawns and fields, flattening uneven grass or leveling new soil in 36-inch wide swathes. Rolling may also help plant new seeds for uniform growth and eliminate mole holes. The roller’s drum is crafted in a sturdy polyethylene, which resists dents, rust, and weather damage. Powder-baked paint provides further protection. Agri-Fab welded the seams on the drum with rounded edges to prevent any uneven grooves while also providing a leak-proof seal. A brass plug closes the 1-inch filling hole. To remove debris, the roller includes a poly scraper bar. A center baffler provides additional stability to ensure the polyethylene drum does not flex and loose its shape. A hitch pin accompanies the roller to accommodate a trouble-free hook up. The roller is shipped without fill for easy transportation. Users who fill the roller drum with water should drain the drum before winter to ensure the water does not freeze and crack the polyethylene. For user who prefer to fill with sand, Agri-Fab recommends filling the drum only halfway full...

  • Brand: Agri-Fab
  • ASIN: B00004RANH
  • UPC: 052613452684

Waterway Plastics 310-1150SD 3 Hp High Flo Spa Wet End, 3 lb

Waterway Plastics 310-1150SD 3 Hp High Flo Spa

Wet end 3 HP high Flo 2". manufacturer: Waterway plastics is proud to design, engineer & produce our quality line of products right here in the USA.

  • Brand: Waterway Plastics
  • ASIN: B004VTFYFW
  • UPC: 806105061744

Seal Spa Hot Tub Pump Wet End Seal Kit fits Guangdong LX Pumps How to Video

Seal Spa Hot Tub Pump Wet End Seal

This Seal Kit is used ONLY in Guangdong LX Brand Wet Ends and includes the Seal, Tool and Silicon. If you have a Jacuzzi Premium or Sundance Hot Tub this seal will not fit even though you may have the same numbers check Hot Tub Parts of America.. This Seal is 1 39/64" Across the back of the Spring Seal part that goes into the volute or wetend back and the Ceramic & Rubber part that goes into the impeller is 1 11/32". The Hole in the ceramic part is about 3/4" and the hole in the spring side measures about 45/64". Note: This Seal Fits Guangdong Chinese LX and LP series Pumps only Some Pump Part numbers are as follows: (WUA200-II/WUA300-II/WUA400-II/WUA200-I/WUA300-I/WUA400-I) (LP200/LP250/LP300/LP150) (WP200-II/WP250-II/WP300-II/WP200-I/250-I/300-I/400-I) To Install you should put silicon sealant on the back of the Metal part and gently push it into place with a 1" coupler as the push tool. Also the rubber part can use a light coat of silicon to slide it into place in the impeller. We offer these alone, with The Professor's Silly Juice or with an Impeller in a kit so look in our store. Note: We offer this seal with the seal too and silicon, with the seal tool and silicon and bearings or the seal with the seal tool, silicon and an impeller in our store. Choose with care, I Do Not a...

  • Brand: American Spa Parts
  • ASIN: B01AWXK3LU
  • UPC: 740016014119

American Spa Parts Waterway Executive 5HP Impeller 56 Frame Pump Wet End Hot Tub Spa How To Video

American Spa Parts Waterway Executive 5HP Impeller 56

Look for How To Video on YouTube "Spa Hot Tub Waterway Executive Pump Seal Impeller & Bearing Replacement How To The Spa Guy" This is an 5HP Impeller for an Executive 48 Frame Wet End up to 5HP Motor and a 56 Frame Wet End 5HP Motor. This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you replace the Impeller. We offer a Seal, Silicone and Impeller individually or in a kit, and the Purpose of this Kit is to repair a Damaged Impeller and Seal inside the Wet End. This is (1) Impeller ONLY!! NOTE: A 5HP Pump is really rare so check your Amperage against Horse Power this impeller should be on a motor with 16 Amps on high speed... Don't Guess Know.. Choose with care... Look for How To Video on YouTube "Spa Hot Tub Waterway Executive Pump Seal Impeller & Bearing Replacement How To The Spa Guy"

  • Brand: American Spa Parts
  • ASIN: B01K39Y756
  • UPC: 740016014423

Aqua Flo AF9104181500 1-1/2 hp, 2", 48 frame

Aqua Flo AF9104181500 1-1/2 hp, 2", 48

Aqua Flo - 1-1/2 hp, 2", 48 frame

  • Brand: Aqua Flo
  • ASIN: B0087N3A22
Similar 48 Frame Replacement Wet End Results
48 Frame Replacement Wet End Video Results

Spa Hot Tub Waterway Executive Pump Seal Impeller & Bearing Replacement How To The Spa Guy 315-1220

48 Frame Replacement Wet End

For parts for this Waterway Pump click here: https://hottubpartsofamerica.com/search.php?search_query=executive+In this video The Spa Guy Replaces the bearing and seal and impeller on a Waterway Executive pump and motor to show you how to do the repair...

  • Likes: 563
  • View count: 164926
  • Dislikes: 27
  • Comments:
Tags: spa,hottub,hot,tub,part,parts,jacuzzi,how to,the spa guy,hot tub parts of america,waterway,pump,p...

Spa Hot Tub Waterway Pump Wet End Seal Repair How To Video

48 Frame Replacement Wet End

This video is about how to install a seal in a Waterway Pump Wet End. We offer many kits for this repair, seals, seals with silicon and impellers or impellers with seals. Find us at eBay or Amazon www.americanspaparts.com

  • Likes: 32
  • View count: 38051
  • Dislikes: 6
  • Comments:
Tags: spa,hot tub,jacuzzi,waterway pump seal,water way pump seal,waterway wet end seal,100 seal,p-1000 ...

Removing a Stuck Impeller on a Hot Tub Pump How To Spa Guy

48 Frame Replacement Wet End

This video is about The Spa Guy showing You How To Remove a Stuck Pump Impeller...This technique is similar for all brands of pumps and motors... www.HotTubPartsofAmerica.com

  • Likes: 170
  • View count: 70591
  • Dislikes: 18
  • Comments:
Tags: spaguy,spa guy,impeller,stuck,how to,aqauflo,aqua-flo,aqua flo,waterway,cmp,sta-rite,vico,starite...

The Spa Guy Parts Videos J Pump Wet End How To

48 Frame Replacement Wet End

This video is about J Pump Wet Ends and the differences in this type wet end and others as well as some pointers to what can go wrong with these wet ends. www.hottubpartsofamerica.com

  • Likes: 3
  • View count: 722
  • Dislikes: 0
  • Comments:
Tags: j pump wet end,j pump,spa j pump,hot tub j pump,jacuzzi j pump,jacuzzi wet end,jacuzzi pump

How To Determine Which Wet End to Order Waterway Hot Tub Pump Executive Series The Spa Guy

48 Frame Replacement Wet End

This video is about Waterway Hot Tub Pump Executive Series How To Determine Which Wet End to Order The Spa Guy.. wwwHotTubPartsofAmerica.com

  • Likes: 4
  • View count: 2516
  • Dislikes: 0
  • Comments:
Tags: spa,hottub,thespaguy,spa guy,waterway,wet end,executive,pump,pumps,part,parts