HPI Racing 87132 Roto Start 2 System Nitro Star 12/15/18

HPI Racing 87132 Roto Start 2 System Nitro

This is the HPI Roto Start 2 Electric Shaft Drive Starter System for the HPI Nitro Star .12/.15/.18 size engines with a pull starter.

  • Brand: HPI Racing
  • ASIN: B000FAN13I

HPI Racing 111600 Nitro Star F3.5 V2 w/Pullstart

HPI Racing 111600 Nitro Star F3.5 V2

FEATURES: ABC construction, Aluminum piston with Brass liner that is Chrome plated Slide valve 2-needle carburetor with composite body that reduces heat transfer and helps prevent vaporization of fuel Race legal .21 cu in (3.5cc) displacement 22g lighter and 4mm taller than previous version Two stage air filter with splash cover Pull starter with one-way bearing encased in a 14mm hex for increased durability Two year limited warranty beginning at date of purchase INCLUDES: Nitro Star F3.5 V2 Engine with Pull Starter, R5 Glow Plug, Air Filter and Instructions REQUIRES: Glow Fuel: Car blend with 20-25% nitro content, use 20% for break- in Air filter oil SPECS: Displacement: .21 cu in (3.5cc) Carburetor Settings: High Speed Needle, 2-2/2 turns clockwise from flush Idle Screw: Set throttle trim on transmitter so that throttle is in neutral position, turn screw counter-clockwise to reduce idle speed, or clockwise to increase idle speed. Set idle speed high enough to keep engine running smoothly, but not high enough to engage the clutch. Low Speed Needle: No adjustment recommended. For increased performance, set after high-speed needle is adjusted. Turn needle in 1/8 turn increments for better bottom end throttle response. Caution-never turn in more than 2 turns from flush. This will c...

  • Brand: HPI Racing
  • ASIN: B00FAR3COY

HPI Racing 107824 Nitro Star G3.0 HO Engine with Pullstart

HPI Racing 107824 Nitro Star G3.0 HO Engine

This is the HPI Nitro Star G3.0 High Output Engine with Pull Starter. The HPI G3.0 HO engine is the high output (HO) version of the well-known HPI G3.0 engine (#101310). The new high output version is optimsed for performance and durability without compromising on run time. A finned black-coated crankcase design not only adds strength and rigidity but will also help cool the engine. HPI's WR8 Rally car (#106950) comes preinstalled with the G3.0 HO engine. Specification for G3.0 HO: Capacity :2.95cc Bore: 16.8mm Stroke 13.6mm RPM : 30000 Practical RPM: 6500~32000 Power : 2.2 ps/kw Carburettor: Composite Slide,7mm Bore Includes: G3.0 High Output Engine with Pull Starter, Carburetor, R5 Cold Glow Plug, Foam Air Filter, three Zip Ties and Instructions Requirements: Fuel: Car blend with 20-25% nitro content Track Equipment: Glow starter, fuel tubing, glow plug wrench

  • Brand: HPI Racing
  • ASIN: B008ETGJZO

HPI Racing 87127 Back Plate Unit for Nitro Star K Series with Pullstart

HPI Racing 87127 Back Plate Unit for Nitro

Back Plate Unit For Nitro Star K Series/Pullstart

  • Brand: HPI Racing
  • ASIN: B000BMVZOC
  • UPC: 743181430630

HPI RACING 111600 Nitro Star F3.5 V2 Engine w/Pullstart by HPI Racing

HPI RACING 111600 Nitro Star F3.5 V2 Engine

  • ASIN: B01LW5OKSA

HPI RACING 111595 Nitro Star F4.6 V2 Engine w/PS by HPI Racing

HPI RACING 111595 Nitro Star F4.6 V2 Engine

Brand new item. Sealed in original package.

  • Brand: HPI Racing
  • ASIN: B01LW0KFNR

HRP New Nitro Star F4.6 V2 Engine With Pullstart

HRP New Nitro Star F4.6 V2 Engine With

FEATURES: Fits any HPI Savage or other 1/8 scale monster truck 1.3oz (37g) lighter and 0.47 (12mm) shorter than previous version Larger fins on cylinder head for improved cooling New pull starter uses one-way bearing encased in a large 14mm hex for increased durability Composite body slide valve F1 7.5mm carburetor 8 ports, 7 intake, one exhaust Two year limited warranty begining at date of purchase, Valid only on engines sold and used in the USA, Canada, and South America INCLUDES: F4.6 V2 Monster Truck Engine with Pull Starter, Cold R5 Glow Plug, Air Filter, and Instructions REQUIRES: Glow Fuel: 15-25% car blend, 20% required for break-in Air filter oil Glow starter and track equipment SPECS: Displacement: 4.6cc Bore: 18.68mm Stroke: 16.6mm Power: 2.9hp @ 32,000RPM Distance between Mounting Hole Centers/Same Side: 083 (21mm) Distance between Mounting Hole Centers/Opposite Side: 1.46 (37.2mm) Crankcase Width below Mounting Tabs: 1.25 (32mm) Width at Mounting Tabs: 1.8 (46mm) Height/bottom of Mounting Tab/top of Cylinder Head: 3.5 (88mm) Height/bottom of Crankcase/top of Cylinder Head: 4 (102mm) Length/Pull Starter to Front Bearing: 3.3 (84mm) Length/Pull Starter to end of Crankshaft: 4.5 (114mm) Carburetor Settings: High Speed Needle, 2-2/2 turns clockwise from flush Idle Screw:...

  • Brand: HPI Racing
  • ASIN: B00FAQZG4E

HPI 1/10 Bullet MT ST Nitro Star G3.0 SLIDE CARBURETOR & AIR FILTER Carb

HPI 1/10 Bullet MT ST Nitro Star G3.0

HPI 1/10 Bullet MT / ST 3.0 Nitro (Model 107004 107006)Nitro Star G3.0 Slide Valve Carburetor & Air FilterMSRP: $90.99This Product Includes:Slide Valve Carburetor (Part # 101277)Carburetor Body (No Part #)Idle Adjustment Screw (Part # 101276)Throttle Slide Drum (Part # 101272)Mid-Range Needle Valve with O-Rings (Part # 101275)Fuel Line Fitting (Part # 1473)Throttle Boot and O-Rings (Part # 101266)Main Needle (Part # 1471)Main Needle Valve Holder (Part # 1470)Fuel Line Fitting (Part # 1473)Water Resistant Air Filter Set (Part # 101831)Air Filter Foam Element (Part # 101652 Partial)Two (2) Nylon Tie Straps (Part # 100329 Partia This product is NEW in OEM Packaging and is from a New, Unused HPI 1/10 Bullet MT / ST 3.0 Nitro (Model 107004 107006)Part Numbers are for Reference Only. The parts included with this product are exclusive to what is pictured in this listing.This product is compatible with the following Model: HPI 1/10 Bullet MT / ST 3.0 Nitro (Model 107004 107006)

  • Brand: HPI Racing
  • ASIN: B00NT5OLX0
  • UPC: 015568419638

HPI 1/10 Bullet MT ST Nitro Star G3.0 * FLYWHEEL, CLUTCH BELL, SHOES & BEARINGS

HPI 1/10 Bullet MT ST Nitro Star G3.0

HPI 1/10 Bullet MT / ST 3.0 Nitro (Model 107004 107006)Nitro Star G3.0 Flywheel, Clutch Bell, Shoes, Springs & BearingsMSRP: $50.99This Product Includes:Two (2) 5x10mm Bearings (Part # B021)13 Tooth Clutch Bell (Part # 101037)Steel ConstructionClutch Shoes (Part # 101047)Clutch Spring (Part # 101048)Flywheel (Part # 101251)Two (2) Pin DesignMetal ConstructionClutch Nut (Part # 101062)Brass Collet (Part # 1420)Six (6) 5x10.5 Washers (Part # Z694 Partial)One (1) 3x6mm Cap Head Screw (Part # Z541 Partial)One (1) 3x8mm Washer (Part # Z224 Partial)This product is NEW in OEM Packaging and is from a New, Unused HPI 1/10 Bullet MT / ST 3.0 Nitro (Model 107004 107006)Part Numbers are for Reference Only. The parts included with this product are exclusive to what is pictured in this listing.This product is compatible with the following Model: HPI 1/10 Bullet MT / ST 3.0 Nitro (Model 107004 107006)

  • Brand: HPI Racing
  • ASIN: B00NT5OLLC
  • UPC: 015568419669

HPI 15105 Nitro Star G3.0 Engine w/PS

HPI 15105 Nitro Star G3.0 Engine

BRAND NEW HPI ENGINE REMOVED FROM A BOXED HPI PRODUCT. COMES WITH THE CARBURETOR AND AIR FILTER, 15105 NITRO STAR 3.0 ENGINE W/PULLSTART

  • Brand: HPI Racing
  • ASIN: B074Q2WKGQ

HPI Racing 107012 Trophy 3.5 Buggy RTR

HPI Racing 107012 Trophy 3.5 Buggy

FEATURES: Chassis: 6061 aluminum 0.12 (3mm) thick with front and rear metal rod braces Drive: Four wheel shaft, with steel outdrives and axles Engine: HPI Nitro Star F3.5 .21 cu in, 2.5hp race legal, pull starter two-stage air filter with splash guard to prevent engine from getting flooded with water in wet conditions, composite 2-needle carb, ABC construction and large heatsink for efficient heat dissipation Radio: 3-channel 2.4GHz with end point adjustment, servo reversing, steering dual rate, failsafe and waterproof servos for steering and throttle Radio Tray: Low profile aluminum Fuel Tank: 5.4oz (160cc) Differentials: Bevel Gear type with four internal gears for increased durability Shocks: Oil-filled aluminum body Shock Towers: 6061 aluminum Brake: Dual drilled steel discs with fiber brake pads Suspension: Extra long arms for greater stability and thick suspension pins for greater resistance against crash damage Spur Gear: 46 tooth steel Steering: Bellcrank type with cast aluminum knuckles and servo saver Steering servo: SF-10W Servo, waterproof/4.5kg-cm6.0V (HPIM4105) Body: Painted and trimmed, black rear wing Bumpers: Front plastic Wheels: Seven spoke black in color, 1.6 (42mm) wide, 3.1 (80mm) diameter Tires: Team HB Proto with large lugs for high traction, 1.6 (41.8mm) ...

  • Brand: HPI Racing
  • ASIN: B007KN3BEC

HPI 1/10 Bullet MT ST Nitro Star G3.0 CRANKCASE, CRANKSHAFT, BEARINGS & MOUNTS

HPI 1/10 Bullet MT ST Nitro Star G3.0

HPI 1/10 Bullet MT / ST 3.0 Nitro (Model 107004 107006)Nitro Star G3.0 Crankase, Crankshaft, Bearings & Engine MountsMSRP: $96.99This Product Includes:Nitro Star G3.0 Crankcase with installed Bearings (Part # 15145)Front Bearing 7x19x6mm (Part # 101586)Rear Bearing 12x21x5mm (Part # 112843)Carburetor Lock Pin (Part # 151131)Nitro Star G3.0 Crankshaft (Part # 15146)Starter Pin and Spring (Part # 1433)Engine Mounts (Part # 101203)Metal ConstructionFour (4) Cap Head Screws Four (4) Spring Washers (Part # Z800 Partial)This product is NEW in OEM Packaging and is from a New, Unused HPI 1/10 Bullet MT / ST 3.0 Nitro (Model 107004 107006)Part Numbers are for Reference Only. The parts included with this product are exclusive to what is pictured in this listing.This product is compatible with the following Model: HPI 1/10 Bullet MT / ST 3.0 Nitro (Model 107004 107006)

  • Brand: HPI Racing
  • ASIN: B00NT5OQ9Y
  • UPC: 015568419683

HPI Racing 120037 Ken Block GYM8 Flux Ford Fiesta ST RX43 WR8 3.0 (Nitro)

HPI Racing 120037 Ken Block GYM8 Flux Ford

The HPI WR8 Nitro Ken Block Gymkhana Ford Fiesta ST RX43 RTR features awesome iridescent "Stars and Stripes" livery on the HPI Racing WR8 chassis! With the fabulous realism of the engine-powered WR8 NITRO, Ken Block fans have their choice of amazing scale replicas of Ken Block's feature car from the Dubai Gymkhana 8 video, and the Terrakhana video, filmed in the desert of southern Utah! The first thing to grab your attention with these cars are the amazing iridescent stars and stripes that cover the officially licensed Ford Fiesta ST RX43 body! As you watch, the color actually changes before your eyes! From purple, to gold, then finally to green - and back again! Of course, the car is covered in the official Hoonigan Racing Division logos, plus sponsor logos such as Toyo, Pennzoil, KB43 and more, AND replica fifteen52 wheels fitted with grippy semi-slick rubber tires for the complete Gymkhana look! The WR8 NITRO chassis uses almost all of the same parts as the brushless FLUX version, but swaps the electric motor with a Nitro engine for total scale realism! With the Nitro Star G3.0 engine, you get a realistic miniature car, complete with fuel system, exhaust and starter for a real racing car experience. Using model engine fuel formulated for RC cars (available from any RC model sh...

  • Brand: HPI Racing
  • ASIN: B07P2GMVT1

HPI 10 Bullet MT / ST Nitro Star G3.0 Recoil Pull Start & Screws

HPI 10 Bullet MT / ST Nitro Star

HPI 1/10 Bullet MT / ST 3.0 Nitro (Model 107004 107006)Nitro Star G3.0 Recoil Pull Start & ScrewsMSRP: $27.99This Product Includes:Nitro Star G3.0 Pull Start (Part # 1428) Factory Assembled 12MM Hex Recoil Assembly IncludedThree (3) 2.6x6mm Cover Plate Screws (Part # 1427 Partial)This product is NEW in OEM Packaging and is from a New, Unused HPI 1/10 Bullet MT / ST 3.0 Nitro (Model 107004 107006)Part Numbers are for Reference Only. The parts included with this product are exclusive to what is pictured in this listing.This product is compatible with the following Model: HPI 1/10 Bullet MT / ST 3.0 Nitro (Model 107004 107006)

  • Brand: HPI Racing
  • ASIN: B00NT5OZ18
  • UPC: 015568419768

HPI Racing 15126 Pullstart Assay (Without One-Way Bearing)

HPI Racing 15126 Pullstart Assay (Without One-Way

Pullstart Assy W/O One-Way Bearing

  • Brand: HPI Racing
  • ASIN: B000BLJ2UC
  • UPC: 885440528358

HPI Racing 101310 Slide Carb with Pull Start G3.0

HPI Racing 101310 Slide Carb with Pull Start

This is the Nitro Star G3.0 Engine with Pullstarter supplied with the HPI Bullet ST 3.0 Monster Truck and Bullet ST 3.0 Stadium Truck.

  • Brand: HPI Racing
  • ASIN: B003RAGC4S

HPI Racing 21BB Nitro Star Engine Underhead Button #1417 by HPI Racing

HPI Racing 21BB Nitro Star Engine Underhead Button

Underhead F3.5;Miscellaneous;Heatsink Head;Genuine HPI quality spare part for easy maintenance and repairs.;Car Nitro Engine Accessories

  • ASIN: B017JHR44G
  • UPC: 785924234266

HPI Racing 1409 Cap Head Screw M3.5x16mm (4) Nitro Star F4.6

HPI Racing 1409 Cap Head Screw M3.5x16mm (4)

HPI cap head screws are constructed of black steel, with a 2.5mm hex socket.Length: .62" (16mm)Diameter: .13" (3.5mm)

  • Brand: HPI Racing
  • ASIN: B001BHK96G

HPI 15222 Crankshaft Nitro Star K4.6 by HPI Racing

HPI 15222 Crankshaft Nitro Star K4.6 by HPI

  • ASIN: B01LW9F8GP

HPI 15135 Starting Shaft 6x20x20mm (Nitro Star T-15L) by HPI Racing

HPI 15135 Starting Shaft 6x20x20mm (Nitro Star T-15L)

(From Amazon.co.jp) NITROMONSTERKING / WHEELYKING4WDRTR:.. Fit HPI, engine system parts

  • ASIN: B01L36G21U
  • UPC: 736126231270

HPI 87199 Air Cleaner Sleeve Set for Nitro Star K4.6 by HPI Racing

HPI 87199 Air Cleaner Sleeve Set for Nitro

  • ASIN: B01GGEKJJU

HPI 15266 Uniball Nitro Star K4.6 by HPI Racing

HPI 15266 Uniball Nitro Star K4.6 by HPI

HPI Racing throttle arm is constructed of black steel. Ball size on arm is 4mm Requires: 1.5mm hex wrench to install on carb

  • Brand: HPI Racing
  • ASIN: B01C6O570K
  • UPC: 792158846677

HPI 15144 Under Head Nitro Star G3.0 by HPI Racing

HPI 15144 Under Head Nitro Star G3.0 by

Under Head;Standard Replacement;Heatsink Head;Genuine HPI quality spare part for easy maintenance and repairs.;Car Nitro Engine Accessories

  • ASIN: B017F2C9RW
  • UPC: 785924221983

HPI 15214 Piston Pin/Retainer Set Nitro Star K4.6 by HPI Racing

HPI 15214 Piston Pin/Retainer Set Nitro Star K4.6

HPI Racing piston pin retainer set is constructed of steel with G shaped pins. Piston Pin RetainersLength: 0.59 (15mm) Outer Diameter: 0.20 (5mm)Diameter: 0.18 (4.5mm) Requires: Installing pin through piston and connecting rod and securing with retainersHPI Racing piston pin retainer set is constructed of steel with G shaped pins. Piston Pin RetainersLength: 0.59 (15mm) Outer Diameter: 0.20 (5mm)Diameter: 0.18 (4.5mm) Requires: Installing pin through piston and connecting rod and securing with retainers

  • Brand: HPI Racing
  • ASIN: B00ZDP1Z2Y
  • UPC: 787551076004
Similar Hpi Racing Nitro Star Results
Hpi Racing Nitro Star Video Results

HPI RACING Nitro Star S-25

Hpi Racing Nitro Star

new starting pin / pressure spring for Nitro Star S-25 from Hpi racing hpi racing 1433

  • Likes: 8
  • View count: 1036
  • Dislikes: 2
  • Comments:
Tags: hpi racing 1433

My New 20 year old HPI Nitro Rs4-2, will it even run?

Hpi Racing Nitro Star

So I was cruising EBAY for deals as usual, and came across this well modified HPI nitro RS4-2 RTR rc. Decided that my limit was 100 on auction, and got lucky at only 77 bucks. This model has some of the most desirable mods at the time, 2 speed transmission OS 12 CV-X nitro motor Front belt tens...

  • Likes: 97
  • View count: 7523
  • Dislikes: 2
  • Comments:
Tags: hpi,nitro,hpi nitro rs4,traxxas,4tec,vintage rc car,cool rc,revo,os engine,old rc,nitro motor

HPI Nitro RS4 3 Evo+ First Start and Breakin

Hpi Racing Nitro Star

I fired it up as quick as I could...LOL....Can't wait to get some radar runs in so I can get some numbers. Thanks for watching. Any questions or comments please leave them below. http://www.asiatees.com

  • Likes: 161
  • View count: 40254
  • Dislikes: 20
  • Comments:
Tags: hpi,nitro,rs4,evo+,rs4 3,onroad,r/c,rc,radio control,Remote Control (Invention),racing,speed,bash...

HPI Savage Racing Nitro Truck (BIG BLOCK)

Hpi Racing Nitro Star

This is HPI's Nitro Star S-25 Engine With Pullstart. This is the standard engine for the Savage 25 and the Savage SS monster trucks. FEATURES: Slide valve carb with flat-head screwdriver adjustment on needle valve ABC cylinder construction Purple anodized head Rear exhaust round port Flowed and ...

  • Likes: 35
  • View count: 16319
  • Dislikes: 8
  • Comments:
Tags: BIG BLOCK,Pullstart,Pcrc Freaks,38,HPI,Horsepower: 2.5,Glow plug left in,Jump,HPI's Nitro Star S-...

HPI NITRO STAR .18 G3.0 T3.0 REBUILD

Hpi Racing Nitro Star

I saw there was no video on YouTube on how to rebuild these motors and I just got 2 used RS4's so of course I was going to rebuild them, I just got it on camera.

  • Likes: 23
  • View count: 2827
  • Dislikes: 12
  • Comments:
Tags: