Pico TA018 60A AC/DC Current Probe, BNC Connector

Pico TA018 60A AC/DC Current Probe, BNC

The PP264 current clamp is ideal for use with PicoScope automotive oscilloscopes for measuring currents between 10 mA and 60 A. This enables the PicoScope to display current waveforms for fuel injectors and fuel pumps (see waveforms below). The current clamp has two calibration settings, set by a slider switch on the handle of the probe. 1 mV/10 mA (100 mV = 1 A) - use this for testing currents up to 20A. 1 mV/100 mA (10 mV = 1 A) - use this for testing current up to 60A. In use there is no need to break into the circuit or disturb the isolation as the opening jaws simply clamp around the current carrying conductor. No electrical contact is required.

  • Brand: Pico
  • ASIN: B01HBHNRSG

Hantek® AC/DC Current Clamp CC 65 Up To 20 kHz 20mA To 65A DC

Hantek® AC/DC Current Clamp CC 65 Up To

AC/DC frequency range: Up to 20 kHz Effective Measurement Range: 20mA to 65A DC It is a transducer which allows your multimeter to measure current data and enable your oscilloscope to measure the current waveforms. Its current transducer is composed by permalloy and hall element, which linearly transform the AC or DC current to AC or DC current voltage. And if connect to an oscilloscope by BNC type connector, you are able to observe the current waveforms; If connect to a multimeter by banana type connector, you can obtain the current data. Application: Power circuit measurement and malfunction analysis; Motor drive of frequency converter (or other electronics) measurement; Power electronics equipments measurement. Specification: DCA range 1 mV /10mA +/-(1.5%+/-5mA) 10mA ~ 20A 1mV/100mA +/-(2%+/-20mA) 100mA ~ 40A +/-(4%+/-0.3A) 40A ~ 65A ACA range 1mV/10mA +/-(2%+/-30mA) 100mA ~ 10A (40Hz ~ 2KHz) +/-(4%+/-30mA) 100mA ~ 10A (2KHz ~ 10KHz) +/-(6%+/-30mA) 100mA ~ 10A (10KHz ~ 20KHz) +/-(8%+/-30mA) 10A ~ 15A (40Hz ~ 20KHz) 1mV/100mA +/-(2%+/-30mA) 200mA ~ 40A (40Hz ~ 1KHz) +/-(4%+/-30mA) 200mA ~ 40A (1KHz ~ 2KHz) +/-(6%+/-30mA) 200mA ~ 40A (3KHz ~ 5KHz) +/-(8%+/-0.3A) 40A ~ 65A (40Hz ~ 20KHz) Captured Conductor Size   9mm maximum Low Battery Indict...

  • Color: Blue,gray
  • Brand: Hantek
  • ASIN: B06W2KFZLW
  • UPC: 519240055713

Hantek CC650 AC/DC Current Clamp for Hantek&Other Makes Auto Oscilloscopes and DMMs,BNC Plug

Hantek CC650 AC/DC Current Clamp for Hantek&Other Makes

This current clamp allows you to measure current without breaking the circuit.Please note a 9V battery is required to use this clamp but NOT included in the package by Hantek because of shipping restrictions.

  • Brand: Hantek
  • ASIN: B009R15SJG
  • UPC: 608641998542

B&K Precision CP62 AC/DC Oscilloscope Current Clamp Probe, 300 kHz

B&K Precision CP62 AC/DC Oscilloscope Current Clamp Probe,

Model CP62 current probe allows a general purpose oscilloscope to display AC and DC current signals up to 100 A Peak (70 A RMS). The CP62 current probe can also make AC and DC measurements with a multimeter by using the recommended accessory TL62 (BNC-to-banana) plug adapter.

  • Brand: B&K Precision
  • ASIN: B00J3AWA0G
  • UPC: 817050726206

Micsig Oscilloscope ACP1000 AC Current Probe with 5ft BNC Insulated Coaxial Output Cable, Operating Frequency 10Hz-100KHz, Test Current Range 0.1A-1000A

Micsig Oscilloscope ACP1000 AC Current Probe with 5ft

Overview: Micsig ACP1000 AC current Probe is designed for professionals and experts like you. Ideal for measuring distorted current waveforms and harmonics, expanding the measurement range to 1000 A while providing the ultimate measurement flexibility. Great tool for all around electrical troubleshooting and accurate measurement. Specification: * Test Current Range: 0.1A-1000A * Operating Frequency: 10Hz-100kHz * Maximum Primary Current: 2000A(2s) * Output Signal: mV/A * Highest Precision: 1% * Operating Temperature: 5-167℉(-15to 75℃) * Safety Class: CAT III 600V * Maximum Conductor size: 2.05 inches(52mm) * Dimensions: 3 x 8.5 x 1.7 inches(111 x 216 x 45mm) * Output Cable: 1.5m BNC insulated coaxial output cable can connect directly to an oscilloscope, and can be used with multimeter with optional BNC/Banana adapter. WARRANTY: SainSmart is a trusted vendor, we provide 12-month manufacturer warranty on all parts. Please buy with confidence, and feel free to contact us if you have any problem. Package List: 1x Current Oscilloscope Probe kit

  • Brand: Micsig
  • ASIN: B07DKZTWSZ

Low Current Amp Probe Clamp AC/DC 0-60 Amps

Low Current Amp Probe Clamp AC/DC 0-60

This cost-effective low current probe is ideal for capturing waveforms from fuel pumps, injectors, relays, ignition and more. This probe can be used with just about any meter and lab scope capable of measuring DC voltage. This low amp current probe can be used with multimeters and lab scopes and such as the Snap-on MODIS, VANTAGE, VERUS, UEI scopes, Vetronix. In essence it can be used with any scope/meter that displays a voltage in digital or waveform format. This amp probe features shielded wire, shielded housing, and 4mm shrouded banana plugs ensure an accurate signal. Features This current probe has the smallest nose (1" x 1/2") we have found. Zero push button (not wheel). Low battery indicator. Lead terminates to banana plugs. Specifications Size at end of jaw: 1" wide x 1/2" thick x 2-1/4" long Conductor opening: 9mm Test Lead: 5' 9" long, terminates to shrouded Banana Plugs 4mm Probe Housing: 7-3/4" x 2-1/2" Accuracy: ranges from 1.5% to 2% under 20A and up to 8% over 20A. Range: 10mA-60A Frequency response: Up to 20KHz. 1-year warranty.

  • ASIN: B00K0U1N5G
  • UPC: 019372177371

PICO TECHNOLOGY TA167 PROBE, CURRENT, OSCILLOSCOPE

PICO TECHNOLOGY TA167 PROBE, CURRENT,

Pico TA167 BNC 2000A/200A AC/DC Current ClampPico TA167 BNC 2000A/200A Current Clampx200 A / 2000 A (high amps) DC current clampThe 200 A / 2000 A current clamp allows you to measure up to 2000 amps without cutting, or disconnecting or stripping wires. Simply clamp the jaws around the cable to be tested and plug the clamp into your PicoScope.Before the launch of this probe we recommended the TA019 (600 A) for working on the starting and charging systems of petrol passenger cars and the PP253 (2000 A) clamp for high compression diesel engines. The TA167 (200 A / 2000 A) covers both these applications in one probe with improved range and sensitivity, lower noise and faster response.The TA167 features a 200 A mode for better performance at lower currents and has an increased jaw size. It also features an auto power-down facility to save battery life when not in use (this feature can be disabled for battery drain / shutdown current testing).Typical UsesThe wide range of this clamp allows currents to be measured from under 1 amp right up to 2000 amps. It can therefore be used with a PicoScope for many applications including: Battery testing with PicoDiagnostics software Relative compression testing Starter motor testing Alternator output testing Hybrid and EV electric motor currentPic...

  • Brand: Pico
  • ASIN: B011OLPC9C

Fluke 80I-110S AC/DC Current Probe, 600V AC rms Voltage, 70A AC/100A DC Current

Fluke 80I-110S AC/DC Current Probe, 600V AC rms

The 80I-110s is compatible with any fluke ScopeMeter test tool, power harmonics analyzer, oscilloscope, multimeter. It also compitable with other voltage measurement device with BNC input connectors or if using a meter convert the banana plugs to a BNC connector using the adapter. It is designed to provide you with safe, high accuracy measurements for a wide range of applications. The specially designed built-in safety features such as the 600 V rms rating at the input jaws, output cable, and BNC connector enhance work safety in industrial and commercial power distribution systems. The probe is shielded for high noise immunity, to prevent unwanted noise when troubleshooting around noise generating devices like adjustable speed motor drives and ignition systems. Safety rating: IEC 1010 and CSA-C22.2 No. 1010-1 installation category II, working voltage 600V. Output signal: 10A range: 100mV/A; 100A range: 10mV/A. Bandwidth: 1Hz to 20kHz. 10 A, AC/DC, 100 A, AC/DC Nominal current range. 0.1A - 10A AC/DC and 1A - 100A AC/DC Continuous current range. 140 A - 2 kHz Maximum non-destructive current. 3 percent + 50 mA (at 10 A) basic accuracy. DC - 100 kHz Useable frequency. 600 V maximum voltage. 9 V, 55 h battery life. 11.8mm conductor diameter. 1.6m output cable length. 1 year warranty....

  • Brand: Fluke
  • ASIN: B000VRCT06
  • UPC: 785577870767

OTC 3820-06 Low Amp Probe

OTC 3820-06 Low Amp

This is a low amp probe that measures current range: 0-60 ampere AC/DC. It works for ignition coils, fuel injectors, relays, electric motors and parasitic draw. The AC/DC current measurement is non-intrusive.

  • Brand: OTC
  • ASIN: B000F5ECJA
  • UPC: 731413037917

ESI 695 80 Amps DC/AC Low Current Probe

ESI 695 80 Amps DC/AC Low Current

Great tool for accurate measurement of low current. Use with your graphing meter or lab scope to view current waveforms on fuel injectors, fuel pumps, primary ignition coils and more. Also works very well with digital multimeters. Resolution of 10 milliamps is low enough for most parasitic drain testing. In addition the clamp opening of 1/2 inch is large enough to clamp over most negative battery cables for those parasitic drain tests.

  • Brand: Electronic Specialties
  • ASIN: B000FN4IUK
  • UPC: 956258641512

Fluke 323 True-RMS Clamp Meter

Fluke 323 True-RMS Clamp

The Fluke true-rms clamp meter is a great clamp meter for general, grab-and-go troubleshooting needs. The Fluke 323 323-AMZN is ideally suited for current measurements up to 400 a in tight cable compartments.

  • Color: Multicolored
  • Brand: Fluke
  • ASIN: B00AQKIEXY
  • UPC: 642008672379

Hantek _BMT_ Combo 6B New! 1008C / CC-650 Current clamp / 2pcs PP80 60MHz Probe / 2pcs Back pin/BNC to Multi-Meter Adapter / HT201 20:1 Attenuator

Hantek _BMT_ Combo 6B New! 1008C / CC-650

This is the combo 6 for you to vehicle diagnostics area right away. The package includes 1 set New! Hantek 1008C 1 set Hantek CC-650 current clamp 2 pc PP80 of 60 MHz BNC oscilloscope probe 1 pc BNC to Multimeter adapter (for you to connect CC650 easily to a multimeter) 1 pair back pin. 1 pc HT201 20:1 attenuator All packed into 1 box to minimize postage. Strong sales on ebay.

  • Brand: Hantek
  • ASIN: B071RP92Q4
  • UPC: 615264232083

Oscilloscope Multimeter 2.0 Update,LIUMY Professional LED Handheld Oscilloscope Multimeter with 200ksps A/D Automatic Waveform Capture Function,DC/AC Voltage/Current Test,HD Display with Backlight

Oscilloscope Multimeter 2.0 Update,LIUMY Professional LED Handheld Oscilloscope

Why do you choose us: ✔High-tech chip LIUMY LM2001 emphasis on functional combination for field testing process, not to replace the meter. It reflects the high-tech, using a dedicated chip has, as the wave function, you can view the waveform signal 10KHZ within. ✔Extensive detection function and range Features include DC/AC voltag /current, resistance, capacitance, frequency, diode / continuity test. Can be home, school, power plant, work area has excellent performance! ✔Save money As a large number of measuring instruments waveform, you will find LM2001 is the most affordable one, spend the price of a multimeter, you can have a table can be seen, as the wave of the waveform, value for money! Specification: Analog Bandwidth: 0~ 10kHz The maximum real-time sampling rate: 200ksps DC voltage: 0mV ~ 1000V ± (0.75% rdg + 10dgt) AC voltage: 0 mv ~ 750V ± (1.0% rdg + 10dgt) DC Current: 0mA ~ 20.00A ± (1.2% rdg + 10dgt) AC current: 0mA ~ 20.00A ± (1.5% rdg + 10dgt) Resistance: 0W ~ 20.00MW ± (1.0% rdg + 5dgt) Capacitance: 0nF ~ 200.0μF ± (2% rdg + 10dgt) Frequency: 0kHz ~ 200kHz ± (1.0% rdg + 5dgt), Diode test: open circuit voltage of about 1.5 V, the maximum test current of about 1.5mA. Continuity Test: determine resistance: about 30 Remote control Detection: ...

  • Brand: LIUMY
  • ASIN: B071F1H3PG

General Technologies Corp GTC CM100 1 mA to 100 Amps AC/DC Low Current Clamp Meter

General Technologies Corp GTC CM100 1 mA to

GTC 1 mA to 100 Amps AC/DC low current clamp meter is designed to accurately measure current, current leaks (parasitic draws down to 1mA) and electrical loads from 1mA to 100 amp AC/DC and voltages from 0 to 600 AC/DC. The small diameter (½ inch or 13mm) and narrow jaw makes it ideal for use in confined spaces and on small gauge wires. Other features include resistance measurement functions, audible continuity test, display hold and peak detector.

  • Color: Grey with Yellow Clamp
  • Brand: General Technologies Corp
  • ASIN: B001TCWL1E
  • UPC: 833303000282

Fluke I310S AC/DC Current Probe, +/-100mA Resolution, 300V AC/ DC Voltage, 450A DC, 300A AC rms Current

Fluke I310S AC/DC Current Probe, +/-100mA Resolution, 300V

The i310s current probe is based on hall effect technology for use in measurement of both DC and AC current. The i310s may be used in conjunction with oscilloscopes and other suitable recording instruments for accurate non-intrusive current measurement. Current ranges: 30A and 300A AC rms or +/-45A and 450A DC. Measuring Ranges: +/-45A and 450A DC. Output Sensitivity: 10 mV/A (40A) to 1 mV/A (400A). Resolution: +/-50 mA (40A) to +/-100 mA (400A). Load impedance: greater than 10 k Ohms and less than or equal to 100 pF. Frequency range (small signal): DC to 20 kHz (- 3 dB). Phase shift below 1 kHz, less than 2 degrees. Temperature coefficient: +/-0.1 percent of reading / degree C. Power Supply: 9V Alkaline, MN1604/PP3. Battery life: 30 hours, low battery indicator. Inrush current: 600A AC rms maximum. Accuracy (at +23 degree C): (30A range) +/-1 percent of reading +/-50 mA, (300A range) +/-1 percent of reading +/-300 mA. Bandwidth to meet accuracy specification: 1 kHz. Conductor position sensitivity: +/-1.5 percent relative to centre reading. Working voltage: 300V AC rms or DC. Maximum conductor size: 19mm diameter. Output connection: safety BNC connector, supplied with safety 4mm adaptor. Output zero: manual adjust via thumbwheel. Cable length: 2m. Operating temperature range: -10...

  • Brand: Fluke
  • ASIN: B0012WZZ8M
  • UPC: 095969401241

AEMC MN02 Compact AC Current Probe with 5' Lead, 50mA to 100A Range, 1mA/A Output

AEMC MN02 Compact AC Current Probe with 5'

The MN02 is a small, compact AC current probe. Designed to meet the most stringent demands in industry and electrical contracting, they also meet the latest safety and performance standards. The probe has a measurement range up to 100A RMS which makes it a perfect tool for measurement with DMMs and recorders. The Model MN02 is compatible with any AC ammeter, multimeter, or other current measurement instrument with an input impedance lower than 10ohms. To achieve the stated accuracy, use the probe with an ammeter having an accuracy of 0.75 percent or better. 1mA/A from 1ohms to 10ohms output signals. Designed to EN61326-1, 300V CAT IV, 600V CAT III safety standard. Double insulation. CE mark. Applications: Measuring in breaker panels. Industrial loads. HVAC. Residential and commercial sites. Data logging/recording. General AC current measurements. Shock protection 3.52 oz (100g)/6ms/half-period (IEC 68-2-27). Self-extinguishing capability casing UL94 V2. Vibration resistance IEC 68-2-6. Measures 4-27/63" length by 1-15/32" width by 1-1/64" depth.

  • Brand: AEMC
  • ASIN: B008S076PG
  • UPC: 685338030419

Uni-T B4Q094 UT210E True RMS AC/DC Current Mini Clamp M W Capacitance Tester

Uni-T B4Q094 UT210E True RMS AC/DC Current Mini

Specifications: Display Count: 2000 Auto Range: Yes Jaw Capacity: 17mm True RMS: Yes Diode: Around 3.0V V.F.C.: Yes NCV: Yes Data Hold: Yes Zero Mode: Yes LCD Backlight: Yes Auto Power Of: Around 15 Minutes Continuity Buzzer: Yes Low Battery Indication: 2.5V Input Protection: Yes Input Impedance for DCV: 10M AC Current (A) 2A/20A/100A (±2.5%+5) DC Current (A) 2A/20A/100A (±2%+3) AC Voltage (V) 2V/20V200V/600V (1.0%+3) DC Voltage (V) 200mV/2V/20V200V/600V (±0.7%+3) Resistance (Ω) 200Ω/2KΩ/20KΩ/200KΩ/2MΩ/20MΩ (±1.0%+2) Capacitance (F) 2nF/20nF/200nF/2μF/20μF/200μF/2mF/20mF(±4%+5) General Characteristic Product Net Weight: 170g Product Size: 175mm * 60mm * 33.5mm Power: AAA 1.5V x 2 (Included) LCD Size: 39.3mm * 21.5 mm Package Size: 18.6 * 7.2 * 5.9cm / 7.3 * 2.8 * 2.3in Package Weight: 311g / 11oz Package List: 1 * UNI-T UT210E Mini Clamp Meters (Batteries not Included) 1 * Test Lead 1 * English Manual

  • Color: UT210E-1
  • Brand: Uni-T
  • ASIN: B00O1Q2HOQ
  • UPC: 760079615016

AEMC MN261 Compact AC Current Probe with 5' BNC Connection, 2 Measuring Ranges

AEMC MN261 Compact AC Current Probe with 5'

The Model MN261 is the latest in compact AC current probes. It is designed to meet the most stringent demands in industry and electrical contracting. Model MN261 meets EN 61010, 600V, category III safety standards and is CE Marked and UL approved in Canada and United States. Model MN261 has a 20mm jaw opening and accommodate conductors up to 250MCM. The unique hooked jaw design facilitates clamping and hooking onto conductors. Polycarbonate materials and ultrasonic welding are used throughout to ensure ruggedness and overall lasting reliability. Model MN261 uses tape-wound cores to further improve its high and low end performance. Rated at 200A RMS it has a measurement range to 240A RMS. Measurement range of 0.1 to 24A, 0.5 to 240AAC. Designed for DMMs, loggers, recorders and oscilloscopes. 40Hz to 10kHz response. 100mVAC/AAC - 10mVAC/AAC output signal. Transformation Ratio: Voltage output. Overload: 240A for 10 min ON, 30 min OFF. Limit Operating Conditions: 200A permanently to 1kHz; Derating above 3kHz: 200A x (1/0.333F), F in kHz. Crest Factor: 3 at 200A RMS with an error (due to CF) of 4 percent. Working/Common Mode Voltage: 600Vrms. Output Termination: 5 feet BNC. Operating Temperature: 14 to 131 degree F. Storage Temperature: -40 to 158 degree F. Operating Relative Humidity...

  • Brand: AEMC
  • ASIN: B008S07FRK
  • UPC: 685338030112

Micsig DP10013 Differential High Voltage Probe, 1300V 100MHz 3.5ns Rise Time 50X/500X Attenuation Rate, Tektronix P5200A P5205A P5210A

Micsig DP10013 Differential High Voltage Probe, 1300V 100MHz

Note: We have upgraded the probes for higher quality, they are different from other ones on amazon, please see the detailed in images. You can buy a better oscilloscope probe kit with same money, just buy it. Test, Evaluate & Tinker with Your Oscilloscope Micsig high voltage differential probes DP series are designed for the measurement of high voltage differential signal, to meet the demand for floating measurement. It has 50MHz and 100MHz two models, and has two kinds of different attenuation ranges: 500X, indicate the maximum test voltage is 1300V; 50X presents maximum test voltage is 130V. Designed for professionals and experts alike, this probe works with most oscilloscopes. In the analog days, some in school experienced using the Tektronix P5200A, P5205A, P5210A differential probes. Even back in those days prices for these differential tools were beyond the reach of most of people. But now, hobbies, students and professionals can afford one of two differential models produced by Micsig. Specs - Accuracy: ±2% - Max differential test voltage (DC+ACPK-PK): 130V (50X); 1300V (500X) - Max input common mode voltage (DC+ACPK-PK): 130V (50X); 1300V (500X) - Max Input voltage-to-earth: 1000V CATII - CMRR: >80dB (DC); >60dB (100KHz); >50dB (1MHz) - Input impedance: 10MΩ/1pF (di...

  • Color: Micsig differential probe
  • Brand: CHPOWER
  • ASIN: B0795XQR68
  • UPC: 604348976470

600A DC/AC Current Probe Clamp Meter Oscilloscope Clamp Meter Current Meter Digital Clamp Current Meter with Test Probe

600A DC/AC Current Probe Clamp Meter Oscilloscope Clamp

This current clamp adapter allows you to measure current without breaking the circuit, which should be attached to general multimeters for work. Features:  Measuring Range: 600A DC/AC current. Can measure the current of multimeter and the current waveforms of oscilloscope. Clamp design and only two buttons, easy to operate. Jaw opening of 45mm to measure current without touching or interrupting the circuit. Comes with test probes for convenient measurement.  Includes LED low power indication. Suitable for general multimeters. Specifications: Brand Name:HoldPeak Model:hp-605a Color: Grey + Blue Material: ABS Jaw Opening: 45mm *Measuring Range:  DC Current: 600A AC Current: 600A Signal Output: 1mV/1A Output Impedance: 10K Conversion Accuracy: ±(3.0%rdg+10dgt) Power Supply: 1 * 9V 6F22 Battery(NOT Included) Weight: Approx.327g/11.5oz   Package list: 1 * Clamp Adapter with Test Probes(Battery NOT Included) 1 * User Manual(English) Note:  It should be attached to general multimeter for work.

  • Color: blue
  • Brand: Wal front
  • ASIN: B07PVS64TW
  • UPC: 703633611949

ESI 307M Fuse Buddy Mini Current Loop

ESI 307M Fuse Buddy Mini Current

Plug a Fuse Buddy Current Loop into a circuit and now you can clamp your current probe over the wire to read the amperes draw.

  • Brand: Electronic Specialties
  • ASIN: B0017R5EHO
  • UPC: 855174001472

Pico 2205A PicoScope 2 channel + AWG, 25MHz, Includes probes

Pico 2205A PicoScope 2 channel + AWG, 25MHz,

PicoScope 2 channel + AWG, 25MHz, Includes probesPicoScope 2200A Series:Benchtop performance in a pocket-sized scopexYour complete test & measurement laboratoryYou can use your PicoScope 2000 Series as an advanced oscilloscope, spectrum analyzer, function generator, arbitrary waveform generator and protocol decoder out of the box. Mixed signal models also add a 16 channel logic analyzer. A complete electronics lab in one compact, low-cost, USB-powered unit.The PicoScope 2000A models deliver unbeatable value for money and are ideal for education, hobby and field service use. In the lab the low cost allows one scope per person rather than having to share.High-end oscilloscopeAt the heart of every PicoScope 2000 is an advanced oscilloscope which offers everything you would expect and much more besides: 10,000 waveform circular buffer Up to 80,000 waveforms per second update rate Mask limit testing Advanced math & filtering Measurements with statistics Advanced digital triggering Resolution enhancement to 12 bitsPicoScope 2200A Series Powerful, portable, and versatile The PicoScope 2200A Series oscilloscopes offer a small, light, modern alternative to bulky benchtop devices. You can now fit a 200 MHz, 1 GS/s instrument easily in your laptop bag or even in your pocket! They are perfec...

  • Brand: Pico
  • ASIN: B0153KF4FW

AEMC MN352 Compact AC Current Probe with Jack, 0.1A to 150A Range, 10mV/A Output

AEMC MN352 Compact AC Current Probe with Jack,

The MN352 is a high accuracy and low phase shift AC current probe with voltage output. It is designed for use with DMMs or current measuring instruments with voltage inputs. The voltage output is proportional to the current measured (through the jaws). The MN352 has a jack output that accepts 4mm banana plugs. The MN probe is the latest in compact AC Current probes. Designed to meet the most stringent demands in industry and electrical contracting, they also meet the latest safety and performance standards. Measurement Range: 0.1 to 150A. Transformation Ratio: Voltage output. Output Signal: 10mV/A (1V at 100AAC). Overload: 240A for 10 min ON, 30 min OFF. Frequency Range: 40 to 10kHz. Limit Operating Conditions: 200A permanently to 1kHz; Derating above 3 kHz: 200 A x (1/0.333F), F in kHz. Crest Factor: 3 at 150A RMS with an error (due to CF) of 3 percent. Working Voltage: 600Vrms. Common Mode Voltage: 600Vrms. Influence of Adjacent Conductor:

  • Brand: AEMC
  • ASIN: B008S07J80
  • UPC: 685338030181

Siglent Technologies SDS1202X-E 200 mhz Digital Oscilloscope 2 Channels, Grey

Siglent Technologies SDS1202X-E 200 mhz Digital Oscilloscope 2

200Mhz, 1Gsa/s, The SDS1202X-E Series employs a new generation of Spo technology that provides excellent signal fidelity and performance. The system noise is also lower than similar products in the industry. It has a minimum vertical input range of 500 UV/Div, an innovative digital trigger system with high sensitivity and low jitter, and a waveform capture rate of 400, 000 frames/sec (sequence mode). it also employs a 256-level intensity Grading display function and a color temperature display mode not found in other models in this Class. Siglent’s new oscilloscopes offering supports multiple powerful triggering modes including serial bus triggering. Decoding is standard configuration including IIC, SPI, UART, can, LIN. History waveform recording and sequential triggering enable extended waveform recording and analysis. Another powerful addition is the new 1M points FFT math function that gives the sds1000x-e very high frequency resolution when observing signal Spectra. The new design also includes a hardware co-processor that delivers measurements quickly and accurately. The features and high performance of the sds1000x-e Series cannot be matched else anywhere at this price. Channels 2CH+1EXT, Memory depth :7 Mpts/CH (Dual-Channel); 14 Mpts/CH (Single-Channel)/ data sheet(cont...

  • Color: Grey
  • Brand: Siglent Technologies
  • ASIN: B06XZML6RD
  • UPC: 784672492652
Similar Oscilloscope Current Probe Results
Oscilloscope Current Probe Video Results

How to Measure Current with an Oscilloscope - Take the Mystery Out of Oscilloscope Probing

Oscilloscope Current Probe

You'll be surprised how easy it is to measure current with a scope! Probe Selection Guide ► http://bit.ly/2mtAzeW ◄ Probe Training Kit Download ► http://bit.ly/ProbeTrainingKit ◄ Click to subscribe: http://bit.ly/Scopes_Sub How to measure current with an oscilloscope? You can use the Ohm's law ...

  • Likes: 918
  • View count: 64365
  • Dislikes: 42
  • Comments:
Tags: current,current probe,current probing,oscilloscope,oscilloscopes,probe,probes,oscilloscope probe,...

Homemade DC/AC oscilloscope current clamp

Oscilloscope Current Probe

The clamp works perfect but is not the most professional tool ever, it is more as an example in order to understand the theory. You could always improve it using better OP AMP and a better circuit. It could observe both DC and AC currents with a range up to 9A. I hole you like it. ------------...

  • Likes: 1308
  • View count: 49856
  • Dislikes: 36
  • Comments:
Tags: dc,current,clamp,oscilloscope,homemade,DIY,hall,sensor,AC,circuit,tutorial,3d,printed

Oscilloscope Configuring Current Probe

Oscilloscope Current Probe

  • Likes: 5
  • View count: 2573
  • Dislikes: 0
  • Comments:
Tags:

Current Probes

Oscilloscope Current Probe

A current probe allows for safe and convenient measurements without probing in series with your circuit or adding a shunt.   Learn more about Oscilloscopes: https://beyondmeasure.rigoltech.com/acton/fs/blocks/showLandingPage/a/1579/p/p-0032/t/page/fm/0 DS1000Z Product Page: https://www.rigolna...

  • Likes: 12
  • View count: 1346
  • Dislikes: 0
  • Comments:
Tags: rigol,eevblog,ds1000z,ds1054Z,getting started,oscilloscope,signal intengrity,current probe,curren...

Hantek low cost current probe review and how to use

Oscilloscope Current Probe

Review of Hantek’s current probe model CC-65. This is a 10 mA to 65 Amp AC and DC current probe. It comes with bnc or banana jack input. It has an on/off switch with 2 ranges. It has a power LED and a low power LED, and runs off of a 9 Volt battery. It also has a degaussing button. Please su...

  • Likes: 100
  • View count: 4283
  • Dislikes: 12
  • Comments:
Tags: Current probe,ac current probe,dc current probe,scope current probe,low cost current probe,curren...